 |
|
Compact Chain Bracket
The compact chain brackets can be used on shaft diameters ranging from approximately
1/2" up to 8-1/2" (up to 20" diameter with optional 1500mm long chain ALI
2.116). A minimum clearance of 25/32" is required along the shaft or coupling hub
axis to mount the bracket without interference. Accepts all standard lengths of support posts for maximum versatility.
 Order No. ALI 2.107set (set of 2 pieces, each
with 300mm and 600mm chains)
Order No. ALI
2.113set (set of 2 pieces, each
with 300mm and 600mm chains, and 20 support posts in storage pouch.)
Order No. ALI
2.892set (set of 2 pieces, each
with 300mm and 600mm chains, and 20 support posts, no storage pouch.)
Chains
Chain, 300mm long with threaded rod for shaft
dia. up to 3-1/2"
Order No. ALI 2.114 (1 piece)
Chain, 600mm long with threaded rod for shaft dia. up to
8-1/2"
Order No. ALI 2.115 (1 piece)
Chain, 1500mm long with threaded rod for shaft dia. up to
20"
Order No. ALI 2.116 (1
piece)
Support
Posts
Support post, 115mm (4-1/2")
Order No. ALI 2.170 (1
piece)
Support post, 150mm (6")
Order No. ALI 2.171 (1
piece)
Support post, 200mm (8")
Order No. ALI 2.172 (1
piece)
Support post, 250mm (10")
Order No. ALI 2.173 (1
piece)
Support post, 300mm (12")
Order No. ALI 2.174 (1
piece)
|
 |
|
Magnetic
Bracket
With four powerful magnets providing instantaneous easy mounting of laser or prism against
solid coupling hub, this bracket requires only 3/8" clearance along the shafts.
Allows interchanging support posts for most convenient
height, as desired.
Order No. ALI 2.112set (set of 2 pieces)
Order No. ALI 2.112 (1 piece, one side)
|
Bracket shown not included. |
|
Stationary Position Adapter
For non-rotatable shafts. Fits hub, coupling or shaft diameters 3-1/8" and up. Used
with magnetic brackets ALI 2.112SET. Use only if shaft rotation is impossible! Accuracy of
readings depend on surface condition of coupling, hub, or shaft. Also used to center
magnetic brackets on large diameter couplings, flanges or shafts.
Order No. L 210 for OPTALIGN IR and OPTALIGN
V
(1 piece, one side, includes vertical fine adjustment device.)
Order No. L 220 for
all other systems
(1 piece, one side)
|
 |
|
Magnetic Sliding Bracket
The magnetic sliding bracket is a specialty bracket that allows measurement and alignment
to be performed when one or both shafts cannot be rotated. It is placed against the back
of the solid coupling hub or front face of the uncoupled shaft and slides around from one
measurement position to the next. Suitable for shaft and coupling diameters from approx.
3-1/8" up.
Order No. ALI 2.230 (1 piece, one side)
|
 |
|
Coupling Bolt-Hole Bracket
The bolt-hole brackets are specialty brackets for very large couplings with bolt holes
greater than 1-3/4" diameter. They can be mounted on the back or front of any
ferromagnetic coupling.
Order No. ALI 2.106set (set of 2 pieces)
Order No. ALI 2.106 (1 piece, one side)
|
 
|
|
Narrow Bracket
Only 5/16" thick, these brackets offer an ideal solution to tight squeezes between
coupling and machine housing. The system contains:
1 set (2 pieces) for shaft dia. up to 3-11/16"
1 set (2 pieces) for shaft dia. up to 6-1/4"
Order No. LUD 2.109set
Narrow bracket system (set of 2 pieces) for shaft diameters up to 3-11/16" only,
available under Order No. LUD
2.109LSETOrder No. LUD
2.109
(1 piece for shaft dia. up to 6-1/4", one side)
Order No. LUD 2.109L
(1 piece for shaft dia. up to 3-11/16", one side)
|
Posts shown not included. |
|
Sliding Bore Bracket
The magnetic sliding bore bracket is a specialty bracket that
allows bore measurement. Suitable for bore diameters from approx. 6.5" to 22".
Allows interchanging support posts for most convenient
height, as desired.
Order No.
L 520 (1 piece, one side)
|
|
Bracket shown not included.
|
|
Offset
Adapter
The offset adapter allows use of magnetic
brackets on large flat surfaces (such as coupling faces). Also fits all our other
quick-fit brackets.
Order
No. ALI 2.244L
|
|
Sensor shown not included. |
|
Cardan Bracket
This bracket allows convenient and accurate alignment of machines
joined by cardan shafts over separations of up to 10m (33 ft.) with ROTALIGN/PRO/ULTRA
or 3m (10 ft.) with OPTALIGN PLUS/SERIES, ALIGNEO, OPTALIGN SMART, SMARTALIGN and MASTERLIGN/BASIC and shaft
offsets of up to 900mm (35-3/8").
Order
No. ALI 2.893set
View
Application Photos
|
Sensors and chain bracket shown not included.
|
|
Cardan Bracket
'Lite'
This bracket allows convenient and accurate alignment of machines
joined by cardan shafts over separations of up to 10m (33 ft.) with ROTALIGN/PRO/ULTRA
or 3m (10 ft.) with OPTALIGN PLUS/SERIES, ALIGNEO, OPTALIGN SMART,
SMARTALIGN and MASTERLIGN/BASIC and shaft
offsets of up to 400mm (15-3/4").
Order
No. ALI 2.874set
View
Application Photos |
Sensor shown not included.
|
|
M3 (Measuring
Machine Movement) Bracket
This bracket allows Measurement of Positional Change (i.e., Thermal
Growth)
Order
No. L 580set (set of 2 pieces) for Rotalign/PRO/ULTRA
Order
No. L 585set (set of 2 pieces) for Optalign PLUS, ALIGNEO, OPTALIGN SMART,
MASTERLIGN/BASIC and
SMARTALIGN
More details |
|
|
|
|
|
Shaft Alignment Brackets Brochure (PDF)
Parts Catalog
(PDF) Straightness
Brackets Bore
Alignment Brackets |
|
|
